耐酒精金属油墨

耐酒精金属油墨

• 贸易信息：
• 价格：200 元/公斤
  包装：按订单
  产地：德国
  供应地：上海
  

• 产品参数：
• 细度(μm)：1 
  表干时间(h)：4-10分钟 
  干燥时间(h)：24 
  耐擦洗性(次)：500 
  耐水性(25℃)：24小时 
  附着力：100 
  粘度(cps)：100 
  固体含量(%)：0.001 
  保质期：72 
  稀释剂：783 
  产品规格：1kg 
  

• 产品品牌：
• 欧徕斯

• 详细说明：
• 耐酒精金属油墨+耐酒精金属自干油墨+耐酒精自干金属油墨 金属系列油墨 油墨特性： 拥有高光高色泽，主要用于金属表面、白铁表面、不锈钢表面、玻璃表面、UV表面、强化表面、电镀表面等材料上，具有高色泽、高色彩、高遮盖力、高稳定性、耐酒精及耐磨擦之特点。 印刷：丝印移印均可。 表干及实干时间：表干时间自然挥发5-10分钟；实干时间在24小时以内(加专用固化剂)。 稀释及清洗：SV3慢干开油水、UVK1（移印开油水）同时可使用718洗网水清洗。 测试方法（完全干燥后）： 1、3m胶纸粘在画有百格的油墨表面，45度角迅速拉起不脱油; 2、纯度99%的工业酒精，一千克砝码用棉布包住在油墨表面，以水平力来回拉200次无脱色; 3、 耐磨：橡皮擦500g力水平来回擦500次。 使用方法： 1、使用前应充分搅拌，用后随时封闭； 2、搅拌时加开油水10-15%，稀释到印刷粘度如需自干加专用固化剂5%-10%. 3、网板塞网时可用洗网水清洗； 4、不得与其它类型油墨混合使用。 注意事项： 1、塑胶材料的外观相似，但可能会是不同的材料，客户需试印确定其符合要求后，再批量印刷； 2、在移印过程中，如出现拉丝或散开，可适当加入一些慢干膏即可; 3、环境温度过高，将会影响油墨原有质量； 4、根据气候变化，请远离火源，阴暗环境下存放。 Metal ink series Properties of ink: With high gloss and high color, mainly used for metal surface, the surface of the surface of stainless steel, iron, glass surface, UV surface, enhanced surface, plating and other materials, with a high color, high color, high covering power, high stability, high alcohol and abrasion resistance The characteristics of. Printing: screen printing can be. Surface drying and drying time: surface dry time natural volatile 5-10 minutes; work time within 24 hours ( with special curing agent). Dilution and cleaning: SV3 slow dry open water, UVK1 ( printing open water) can be simultaneously used 718 washing network water cleaning. Test method ( completely dry ): In 1, 3M gummed paper in paintings of the surface of the ink, 45 degree angle quickly pulled off the oil; In 2, 99% of the purity of industrial alcohol, one kilogram of weight of cotton pack in the ink surface, with a horizontal force pulling back and forth 200 times without decolorization; 3: 500g force levels, wear-resistant eraser brush back and forth 500 times. Method of use: In 1, before use should be fully stirred, use at any time after the closure of; 2, add water mixing 10-15%, diluted to printing viscosity for self stem plus special curing agent 5%-10%. 3, mesh plug mesh used when washing network water cleaning; 4, not with other types of ink mixing. Matters needing attention: 1, plastic material similar in appearance, but may be of different materials, customers need to try to determine its requirements, and then bulk printing; 2, in the printing process, such as drawing or spread out, may be appropriate to add some slow dry plaster; In 3, the ambient temperature is too high, will influence the quality of the original ink; In 4, according to climate change, please stay away from fire, dark environment storage.